- 1......1985-86 carbureted Honda Civic/CRX have distributor caps with either vertical or horizontal distributor cap towers. We refer to "vertical" and "horizontal" as the direction of the towers when cap is fitted to the engine. Vertical towers (point upwards): order as for 1987. Horizontal towers (point to the side): order as for 1984.
- 2......1993 Cutlass with 3.1 M engine (for VIN code information see note 1, above) should be ordered as for 1994
- 3......Also see 10mm wire sets, page 19
- 4......Cautiously check the ignition coil tower (male/female) and boot shap if specified (oval/teardrop) before ordering. Orders will not be accepted for refund if the wrong one was ordered.
- 5......Delco: ignition coil pack has 1 row of 6 terminals. Magnavox: ignition coil pack has 2 rows of 3 terminals
- 6......Do not order 7mm cable for 1988-91 Chevrolet & GMC C,K,G,P series trucks and 1991-92 GMC Syclone & Typhoon_____________________________________
- 7......For "post type" distributor caps, the distributor connection on each spark plug wire must be pushed over a terminal at the distributor cap. For "push-in type" distributor caps the distributor connection on each spark plug wire is pushed into the distributor cap tower
- 8......Magnecor R-100 10mm racing spark plug wire sets available for this model--call for more info.
- 9......For 1979 engines: Most engines have the late style Chrysler Corp. ignition coil with an internal spark plug type connection for the coil wire. However, some engines have the earlier type coil. For these engines order as for 1978. Please inquire if unsure.
- 10......For 1992 Celica GT Convertible: For engines where ignition coil is mounted outside of distributor cap, order as for 1991 models
- 11......For 1992 models please note: For engines with 5mm diameter factory wires order as for 1993. For engines with 7mm diameter factory wires order as for 1991
- 12......For 1992 models please note:This set is for engines with integral ignition coil inside distributor. For 1992 models with remote mounted ignition coil order as for 1991
- 13......For 1997: On early engines the wires for cylinders 7 & 8 (left side, rear) are routed around the front of the engine and for late engines around the back of the engine
- 14......For aftermarket supercharged engines order part no. 85267 (8.5mm cable only), which has 3” added to all wires. For twin-turbo modifications order part no. 85278
- 15......For engines fitted with JBA headers order part number 67214 (7mm cable), 60214 (8mm cable) or 65214 (KV85 8.5mm cable)
- 16......For engines with aftermarket headers order part number 87259 (7mm cable), 80259 (8mm cable) or 85259 (KV85 8.5mm cable) - set has 45deg; angle spark plug boots
- 17......For GM cars, the engine code is identified in 1995-81 by the 8th character and in 1980-72 by the 5th character of the VIN number, located on the dash of the vehicle
- 18......IMPORTANT NOTE: These wires are not supplied with inductive pickups, that are used on late model engines (particularly, engines with Motronic 1.3 system or higher). Please inquire if your engine has one.
- 19......Note: this set currently only works for engines without the lower heat shields installed
- 20......Please note: These sets are not always available, inquire before ordering. None of these sets are supplied with brackets or wire looms
- 21......Push-in type distributor cap (standard distributor termination, terminal on spark plug wire pushes into distributor cap tower)
- 22......Screw-in type distributor cap (spark plug wire with no boot or terminal is pushed into a hole in distributor cap, the wire is then locked into place by a pointed screw)
- 23......Sets can be most easily fitted into 2-part rectangular wire retainers if ordered in 7mm cable. We can fit wires into one piece cylindrical wire retainers at extra cost but we suggest that the wires are not fitted into them, as they are a major cause of wire failure. 2-piece retainers, to replace1-piece can be purchased from BMW dealers
- 24......Silent shaft engines have the distributor mounted horizontally into the engine, non-silent shaft (older) engines have the distributor mounted into the engine block.
- 25......Some 1995 engines may have ignition coil mounted on left side of engine, for these order as for 1994 models. Please inquire if unsure
- 26......These sets will only properly fit engines with spark plugs having a 5/8” hex diameter (some original spark plugs were 3/4” diameter).
- 27......This set is for engines fitted with commonly used spark plugs, such as Champion C63YC or similar with a 50mm height from gasket seal to top of spark plug. For engines fitted with factory spark plugs with a 59mm height, a different set has to be supplied. Please inquire if unsure.
- 28......To identify valve covers: Aluminum valve cover is silver in color and non-metallic valve cover is black in color. These wire sets are not interchangeable
- 29......US specification models included here.
- 30......Wire sets for early 1991 Dodge Shadow Convertible with 2.5 engine with ignition coil mounted on the inner right fender should be ordered as for 1990 models.
- 31......With Pontiac engines. For Canadian models with Chevrolet engines, please inquire
- 32......You can purchase factory style red silicone tubing to fit over the 7mm cable if your original tubing is not in good condition, part number is SLV5 - order by the foot
|
